Temporarily make sure that the HA Ingress reconciler does not run,
as we do not want to release this to stable just yet.
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Bumps Alpine 3.18 -> 3.19.
Alpine 3.19 links iptables to nftables-based
implementation that can break hosts that don't
support nftables.
Link iptables back to the legacy implementation
till we have some certainty that changing to
nftables based implementation will not break existing
setups.
Updates tailscale/tailscale#15328
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/{k8s-operator,containerboot}: check TLS cert before advertising VIPService
- Ensures that Ingress status does not advertise port 443 before
TLS cert has been issued
- Ensure that Ingress backends do not advertise a VIPService
before TLS cert has been issued, unless the service also
exposes port 80
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
ipn/store/kubestore: skip cache for the write replica in cert share mode
This is to avoid issues where stale cache after Ingress recreation
causes the certs not to be re-issued.
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/k8s-operator,k8s-operator: allow using LE staging endpoint for Ingress
Allow to optionally use LetsEncrypt staging endpoint to issue
certs for Ingress/HA Ingress, so that it is easier to
experiment with initial Ingress setup without hiting rate limits.
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
If conffile is used to configure tailscaled, always update
currently advertised services from conffile, even if they
are empty in the conffile, to ensure that it is possible
to transition to a state where no services are advertised.
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/k8s-operator: configure HA Ingress replicas to share certs
Creates TLS certs Secret and RBAC that allows HA Ingress replicas
to read/write to the Secret.
Configures HA Ingress replicas to run in read-only mode.
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
This PR adds some custom logic for reading and writing
kube store values that are TLS certs and keys:
1) when store is initialized, lookup additional
TLS Secrets for this node and if found, load TLS certs
from there
2) if the node runs in certs 'read only' mode and
TLS cert and key are not found in the in-memory store,
look those up in a Secret
3) if the node runs in certs 'read only' mode, run
a daily TLS certs reload to memory to get any
renewed certs
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/containerboot: manage HA Ingress TLS certs from containerboot
When ran as HA Ingress node, containerboot now can determine
whether it should manage TLS certs for the HA Ingress replicas
and call the LocalAPI cert endpoint to ensure initial issuance
and renewal of the shared TLS certs.
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* ipn/ipnlocal,envknob: add some primitives for HA replica cert share.
Add an envknob for configuring
an instance's cert store as read-only, so that it
does not attempt to issue or renew TLS credentials,
only reads them from its cert store.
This will be used by the Kubernetes Operator's HA Ingress
to enable multiple replicas serving the same HTTPS endpoint
to be able to share the same cert.
Also some minor refactor to allow adding more tests
for cert retrieval logic.
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/k8s-operator: ensure HA Ingress can operate in multicluster mode.
Update the owner reference mechanism so that:
- if during HA Ingress resource creation, a VIPService
with some other operator's owner reference is already found,
just update the owner references to add one for this operator
- if during HA Ingress deletion, the VIPService is found to have owner
reference(s) from another operator, don't delete the VIPService, just
remove this operator's owner reference
- requeue after HA Ingress reconciles that resulted in VIPService updates,
to guard against overwrites due to concurrent operations from different
clusters.
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Reads use the sanitized form, so unsanitized keys being stored
in memory resulted lookup failures, for example for serve config.
Updates tailscale/tailscale#15134
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Ensures default Linux umask 022 for the installer script to
make sure that files created by the installer can be accessed
by other tools, such as apt.
Updates tailscale/tailscale#15133
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Hostinfo.WireIngress is used as a hint that the node intends to use
funnel. We now send another field, IngressEnabled, in cases where
funnel is explicitly enabled, and the logic control-side has
been changed to look at IngressEnabled as well as WireIngress in all
cases where previously the hint was used - so we can now stop sending
WireIngress when IngressEnabled is true to save some bandwidth.
Updates tailscale/tailscale#11572
Updates tailscale/corp#25931
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
This change:
- reinstates the HA Ingress controller that was disabled for 1.80 release
- fixes the API calls to manage VIPServices as the API was changed
- triggers the HA Ingress reconciler on ProxyGroup changes
Updates tailscale/tailscale#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
The HA Ingress functionality is not actually doing anything
valuable yet, so don't run the controller in 1.80 release yet.
Updates tailscale/tailscale#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
This change builds on top of #14436 to ensure minimum downtime during egress ProxyGroup update rollouts:
- adds a readiness gate for ProxyGroup replicas that prevents kubelet from marking
the replica Pod as ready before a corresponding readiness condition has been added
to the Pod
- adds a reconciler that reconciles egress ProxyGroup Pods and, for each that is not ready,
if cluster traffic for relevant egress endpoints is routed via this Pod- if so add the
readiness condition to allow kubelet to mark the Pod as ready.
During the sequenced StatefulSet update rollouts kubelet does not restart
a Pod before the previous replica has been updated and marked as ready, so
ensuring that a replica is not marked as ready allows to avoid a temporary
post-update situation where all replicas have been restarted, but none of the
new ones are yet set up as an endpoint for the egress service, so cluster traffic is dropped.
Updates tailscale/tailscale#14326
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Fixes the configfile reload logic- if the tailscale capver can not
yet be determined because the device info is not yet written to the
state Secret, don't assume that the proxy is pre-110.
Updates tailscale/tailscale#13032
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/{containerboot,k8s-operator},kube: add preshutdown hook for egress PG proxies
This change is part of work towards minimizing downtime during update
rollouts of egress ProxyGroup replicas.
This change:
- updates the containerboot health check logic to return Pod IP in headers,
if set
- always runs the health check for egress PG proxies
- updates ClusterIP Services created for PG egress endpoints to include
the health check endpoint
- implements preshutdown endpoint in proxies. The preshutdown endpoint
logic waits till, for all currently configured egress services, the ClusterIP
Service health check endpoint is no longer returned by the shutting-down Pod
(by looking at the new Pod IP header).
- ensures that kubelet is configured to call the preshutdown endpoint
This reduces the possibility that, as replicas are terminated during an update,
a replica gets terminated to which cluster traffic is still being routed via
the ClusterIP Service because kube proxy has not yet updated routig rules.
This is not a perfect check as in practice, it only checks that the kube
proxy on the node on which the proxy runs has updated rules. However, overall
this might be good enough.
The preshutdown logic is disabled if users have configured a custom health check
port via TS_LOCAL_ADDR_PORT env var. This change throws a warnign if so and in
future setting of that env var for operator proxies might be disallowed (as users
shouldn't need to configure this for a Pod directly).
This is backwards compatible with earlier proxy versions.
Updates tailscale/tailscale#14326
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/k8s-operator: add logic to parse L7 Ingresses in HA mode
- Wrap the Tailscale API client used by the Kubernetes Operator
into a client that knows how to manage VIPServices.
- Create/Delete VIPServices and update serve config for L7 Ingresses
for ProxyGroup.
- Ensure that ingress ProxyGroup proxies mount serve config from a shared ConfigMap.
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Adds a new Hostinfo.IngressEnabled bool field that holds whether
funnel is currently enabled for the node. Triggers control update
when this value changes.
Bumps capver so that control can distinguish the new field being false
vs non-existant in previous clients.
This is part of a fix for an issue where nodes with any AllowFunnel
block set in their serve config are being displayed as if actively
routing funnel traffic in the admin panel.
Updates tailscale/tailscale#11572
Updates tailscale/corp#25931
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
We throw error early with a warning if users attempt to enable background funnel
for a node that does not allow incoming connections
(shields up), but if it done in foreground mode, we just silently fail
(the funnel command succeeds, but the connections are not allowed).
This change makes sure that we also error early in foreground mode.
Updates tailscale/tailscale#11049
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/containerboot: load containerboot serve config that does not contain HTTPS endpoint in tailnets with HTTPS disabled
Fixes an issue where, if a tailnet has HTTPS disabled, no serve config
set via TS_SERVE_CONFIG was loaded, even if it does not contain an HTTPS endpoint.
Now for tailnets with HTTPS disabled serve config provided to containerboot is considered invalid
(and therefore not loaded) only if there is an HTTPS endpoint defined in the config.
Fixestailscale/tailscale#14495
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/{k8s-operator,containerboot}: reload tailscaled configfile when its contents have changed
Instead of restarting the Kubernetes Operator proxies each time
tailscaled config has changed, this dynamically reloads the configfile
using the new reload endpoint.
Older annotation based mechanism will be supported till 1.84
to ensure that proxy versions prior to 1.80 keep working with
operator 1.80 and newer.
Updates tailscale/tailscale#13032
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* cmd/k8s-operator,k8s-operator: allow users to set custom labels for the optional ServiceMonitor
Updates tailscale/tailscale#14381
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Currently this does not yet do anything apart from creating
the ProxyGroup resources like StatefulSet.
Updates tailscale/corp#24795
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/containerboot,kube/kubetypes,cmd/k8s-operator: detect if Ingress is created in a tailnet that has no HTTPS
This attempts to make Kubernetes Operator L7 Ingress setup failures more explicit:
- the Ingress resource now only advertises HTTPS endpoint via status.ingress.loadBalancer.hostname when/if the proxy has succesfully loaded serve config
- the proxy attempts to catch cases where HTTPS is disabled for the tailnet and logs a warning
Updates tailscale/tailscale#12079
Updates tailscale/tailscale#10407
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* cmd/k8s-operator,k8s-operator,go.mod: optionally create ServiceMonitor
Adds a new spec.metrics.serviceMonitor field to ProxyClass.
If that's set to true (and metrics are enabled), the operator
will create a Prometheus ServiceMonitor for each proxy to which
the ProxyClass applies.
Additionally, create a metrics Service for each proxy that has
metrics enabled.
Updates tailscale/tailscale#11292
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
We were previously relying on unintended behaviour by runc where
all containers where by default given read/write/mknod permissions
for tun devices.
This behaviour was removed in https://github.com/opencontainers/runc/pull/3468
and released in runc 1.2.
Containerd container runtime, used by Docker and majority of Kubernetes distributions
bumped runc to 1.2 in 1.7.24 https://github.com/containerd/containerd/releases/tag/v1.7.24
thus breaking our reference tun mode Tailscale Kubernetes manifests and Kubernetes
operator proxies.
This PR changes the all Kubernetes container configs that run Tailscale in tun mode
to privileged. This should not be a breaking change because all these containers would
run in a Pod that already has a privileged init container.
Updates tailscale/tailscale#14256
Updates tailscale/tailscale#10814
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Ensure that the ExternalName Service port names are always synced to the
ClusterIP Service, to fix a bug where if users created a Service with
a single unnamed port and later changed to 1+ named ports, the operator
attempted to apply an invalid multi-port Service with an unnamed port.
Also, fixes a small internal issue where not-yet Service status conditons
were lost on a spec update.
Updates tailscale/tailscale#10102
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
A small follow-up to #14112- ensures that the operator itself can emit
Events for its kube state store changes.
Updates tailscale/tailscale#14080
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
This is a follow-up to #14112 where our internal kube client was updated
to allow it to emit Events - this updates our sample kube manifests
and tsrecorder manifest templates so they can benefit from this functionality.
Updates tailscale/tailscale#14080
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Adds functionality to kube client to emit Events.
Updates kube store to emit Events when tailscaled state has been loaded, updated or if any errors where
encountered during those operations.
This should help in cases where an error related to state loading/updating caused the Pod to crash in a loop-
unlike logs of the originally failed container instance, Events associated with the Pod will still be
accessible even after N restarts.
Updates tailscale/tailscale#14080
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Adds a /disconnect-control local API endpoint that just shuts down control client.
This can be run before shutting down an HA subnet router/app connector replica - it will ensure
that all connection to control are dropped and control thus considers this node inactive and tells
peers to switch over to another replica. Meanwhile the existing connections keep working (assuming
that the replica is given some graceful shutdown period).
Updates tailscale/tailscale#14020
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Sets a custom hostinfo app type for ProxyGroup replicas, similarly
to how we do it for all other Kubernetes Operator managed components.
Updates tailscale/tailscale#13406,tailscale/corp#22920
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Make it possible to advertise app connector via a new conffile field.
Also bumps capver - conffile deserialization errors out if unknonw
fields are set, so we need to know which clients understand the new field.
Updates tailscale/tailscale#11113
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Now when we have HA for egress proxies, it makes sense to support topology
spread constraints that would allow users to define more complex
topologies of how proxy Pods need to be deployed in relation with other
Pods/across regions etc.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Cache state in memory on writes, read from memory
in reads.
kubestore was previously always reading state from a Secret.
This change should fix bugs caused by temporary loss of access
to kube API server and imporove overall performance
Fixes#7671
Updates tailscale/tailscale#12079,tailscale/tailscale#13900
Signed-off-by: Maisem Ali <maisem@tailscale.com>
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Co-authored-by: Maisem Ali <maisem@tailscale.com>
cmd/k8s-operator,k8s-operator/apis: set a readiness condition on egress Services
Set a readiness condition on ExternalName Services that define a tailnet target
to route cluster traffic to via a ProxyGroup's proxies. The condition
is set to true if at least one proxy is currently set up to route.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
We don't need to error out and continuously reconcile if ProxyClass
has not (yet) been created, once it gets created the ProxyGroup
reconciler will get triggered.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Currently egress Services for ProxyGroup only work for Pods and Services
with IPv4 addresses. Ensure that it works on dual stack clusters by reading
proxy Pod's IP from the .status.podIPs list that always contains both
IPv4 and IPv6 address (if the Pod has them) rather than .status.podIP that
could contain IPv6 only for a dual stack cluster.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Adds a new reconciler that reconciles ExternalName Services that define a
tailnet target that should be exposed to cluster workloads on a ProxyGroup's
proxies.
The reconciler ensures that for each such service, the config mounted to
the proxies is updated with the tailnet target definition and that
and EndpointSlice and ClusterIP Service are created for the service.
Adds a new reconciler that ensures that as proxy Pods become ready to route
traffic to a tailnet target, the EndpointSlice for the target is updated
with the Pods' endpoints.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
The AddSNATRuleForDst rule was adding a new rule each time it was called including:
- if a rule already existed
- if a rule matching the destination, but with different desired source already existed
This was causing issues especially for the in-progress egress HA proxies work,
where the rules are now refreshed more frequently, so more redundant rules
were being created.
This change:
- only creates the rule if it doesn't already exist
- if a rule for the same dst, but different source is found, delete it
- also ensures that egress proxies refresh firewall rules
if the node's tailnet IP changes
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* cmd/containerboot,kube,util/linuxfw: configure kube egress proxies to route to 1+ tailnet targets
This commit is first part of the work to allow running multiple
replicas of the Kubernetes operator egress proxies per tailnet service +
to allow exposing multiple tailnet services via each proxy replica.
This expands the existing iptables/nftables-based proxy configuration
mechanism.
A proxy can now be configured to route to one or more tailnet targets
via a (mounted) config file that, for each tailnet target, specifies:
- the target's tailnet IP or FQDN
- mappings of container ports to which cluster workloads will send traffic to
tailnet target ports where the traffic should be forwarded.
Example configfile contents:
{
"some-svc": {"tailnetTarget":{"fqdn":"foo.tailnetxyz.ts.net","ports"{"tcp:4006:80":{"protocol":"tcp","matchPort":4006,"targetPort":80},"tcp:4007:443":{"protocol":"tcp","matchPort":4007,"targetPort":443}}}}
}
A proxy that is configured with this config file will configure firewall rules
to route cluster traffic to the tailnet targets. It will then watch the config file
for updates as well as monitor relevant netmap updates and reconfigure firewall
as needed.
This adds a bunch of new iptables/nftables functionality to make it easier to dynamically update
the firewall rules without needing to restart the proxy Pod as well as to make
it easier to debug/understand the rules:
- for iptables, each portmapping is a DNAT rule with a comment pointing
at the 'service',i.e:
-A PREROUTING ! -i tailscale0 -p tcp -m tcp --dport 4006 -m comment --comment "some-svc:tcp:4006 -> tcp:80" -j DNAT --to-destination 100.64.1.18:80
Additionally there is a SNAT rule for each tailnet target, to mask the source address.
- for nftables, a separate prerouting chain is created for each tailnet target
and all the portmapping rules are placed in that chain. This makes it easier
to look up rules and delete services when no longer needed.
(nftables allows hooking a custom chain to a prerouting hook, so no extra work
is needed to ensure that the rules in the service chains are evaluated).
The next steps will be to get the Kubernetes Operator to generate
the configfile and ensure it is mounted to the relevant proxy nodes.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
The operator creates a non-reusable auth key for each of
the cluster proxies that it creates and puts in the tailscaled
configfile mounted to the proxies.
The proxies are always tagged, and their state is persisted
in a Kubernetes Secret, so their node keys are expected to never
be regenerated, so that they don't need to re-auth.
Some tailnet configurations however have seen issues where the auth
keys being left in the tailscaled configfile cause the proxies
to end up in unauthorized state after a restart at a later point
in time.
Currently, we have not found a way to reproduce this issue,
however this commit removes the auth key from the config once
the proxy can be assumed to have logged in.
If an existing, logged-in proxy is upgraded to this version,
its redundant auth key will be removed from the conffile.
If an existing, logged-in proxy is downgraded from this version
to a previous version, it will work as before without re-issuing key
as the previous code did not enforce that a key must be present.
Updates tailscale/tailscale#13451
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Rename kube/{types,client,api} -> kube/{kubetypes,kubeclient,kubeapi}
so that we don't need to rename the package on each import to
convey that it's kubernetes specific.
Updates#cleanup
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Further split kube package into kube/{client,api,types}. This is so that
consumers who only need constants/static types don't have to import
the client and api bits.
Updates#cleanup
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* cmd/k8s-operator,k8s-operator/sessonrecording: ensure CastHeader contains terminal size
For tsrecorder to be able to play session recordings, the recording's
CastHeader must have '.Width' and '.Height' fields set to non-zero.
Kubectl (or whoever is the client that initiates the 'kubectl exec'
session recording) sends the terminal dimensions in a resize message that
the API server proxy can intercept, however that races with the first server
message that we need to record.
This PR ensures we wait for the terminal dimensions to be processed from
the first resize message before any other data is sent, so that for all
sessions with terminal attached, the header of the session recording
contains the terminal dimensions and the recording can be played by tsrecorder.
Updates tailscale/tailscale#19821
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/k8s-operator,k8s-operator/sessionrecording: support recording WebSocket sessions
Kubernetes currently supports two streaming protocols, SPDY and WebSockets.
WebSockets are replacing SPDY, see
https://github.com/kubernetes/enhancements/issues/4006.
We were currently only supporting SPDY, erroring out if session
was not SPDY and relying on the kube's built-in SPDY fallback.
This PR:
- adds support for parsing contents of 'kubectl exec' sessions streamed
over WebSockets
- adds logic to distinguish 'kubectl exec' requests for a SPDY/WebSockets
sessions and call the relevant handler
Updates tailscale/corp#19821
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Co-authored-by: Tom Proctor <tomhjp@users.noreply.github.com>
Add functionality to optionally serve a health check endpoint
(off by default).
Users can enable health check endpoint by setting
TS_HEALTHCHECK_ADDR_PORT to [<addr>]:<port>.
Containerboot will then serve an unauthenticatd HTTP health check at
/healthz at that address. The health check returns 200 OK if the
node has at least one tailnet IP address, else returns 503.
Updates tailscale/tailscale#12898
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* cmd/k8s-operator: fix DNS reconciler for dual-stack clusters
This fixes a bug where DNS reconciler logic was always assuming
that no more than one EndpointSlice exists for a Service.
In fact, there can be multiple, for example, in dual-stack
clusters, but also in other cases this is valid (as per kube docs).
This PR:
- allows for multiple EndpointSlices
- picks out the ones for IPv4 family
- deduplicates addresses
Updates tailscale/tailscale#13056
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Co-authored-by: Tom Proctor <tomhjp@users.noreply.github.com>
It is no longer correct to state that we don't support running Tailscale in containers or on Kubernetes.
Updates tailscale/tailscale#12842
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Add a warning that the Dockerfile in the OSS repo is not the
currently used mechanism to build the images we publish - for folks
who want to contribute to image build scripts or otherwise need to
understand the image build process that we use.
Updates#cleanup
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/k8s-operator,k8s-operator/sessionrecording,sessionrecording,ssh/tailssh: refactor session recording functionality
Refactor SSH session recording functionality (mostly the bits related to
Kubernetes API server proxy 'kubectl exec' session recording):
- move the session recording bits used by both Tailscale SSH
and the Kubernetes API server proxy into a shared sessionrecording package,
to avoid having the operator to import ssh/tailssh
- move the Kubernetes API server proxy session recording functionality
into a k8s-operator/sessionrecording package, add some abstractions
in preparation for adding support for a second streaming protocol (WebSockets)
Updates tailscale/corp#19821
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Re-instates the functionality that generates CRD API docs, but using
a different library as the one we were using earlier seemed to have
some issues with its Git history.
Also regenerates the docs (make kube-generate-all).
Updates tailscale/tailscale#12859
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
wgengine/magicsock,ipn: allow setting static node endpoints via tailscaled config file.
Adds a new StaticEndpoints field to tailscaled config
that can be used to statically configure the endpoints
that the node advertizes. This field will replace
TS_DEBUG_PRETENDPOINTS env var that can be used to achieve the same.
Additionally adds some functionality that ensures that endpoints
are updated when configfile is reloaded.
Also, refactor configuring/reconfiguring components to use the
same functionality when configfile is parsed the first time or
subsequent times (after reload). Previously a configfile reload
did not result in resetting of prefs. Now it does- but does not yet
tell the relevant components to consume the new prefs. This is to
be done in a follow-up.
Updates tailscale/tailscale#12578
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Remove fybrik.io/crdoc dependency as it is causing issues for folks attempting
to vendor tailscale using GOPROXY=direct.
This means that the CRD API docs in ./k8s-operator/api.md will no longer
be generated- I am going to look at replacing it with another tool
in a follow-up.
Updates tailscale/tailscale#12859
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/k8s-operator,ssh/tailssh,tsnet: optionally record kubectl exec sessions
The Kubernetes operator's API server proxy, when it receives a request
for 'kubectl exec' session now reads 'RecorderAddrs', 'EnforceRecorder'
fields from tailcfg.KubernetesCapRule.
If 'RecorderAddrs' is set to one or more addresses (of a tsrecorder instance(s)),
it attempts to connect to those and sends the session contents
to the recorder before forwarding the request to the kube API
server. If connection cannot be established or fails midway,
it is only allowed if 'EnforceRecorder' is not true (fail open).
Updates tailscale/corp#19821
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Co-authored-by: Maisem Ali <maisem@tailscale.com>
* cmd/containerboot: store device ID before setting up proxy routes.
For containerboot instances whose state needs to be stored
in a Kubernetes Secret, we additonally store the device's
ID, FQDN and IPs.
This is used, between other, by the Kubernetes operator,
who uses the ID to delete the device when resources need
cleaning up and writes the FQDN and IPs on various kube
resource statuses for visibility.
This change shifts storing device ID earlier in the proxy setup flow,
to ensure that if proxy routing setup fails,
the device can still be deleted.
Updates tailscale/tailscale#12146
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* code review feedback
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
---------
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Fix a bug where, for a subnet router that advertizes
4via6 route, all packets with a source IP matching
the 4via6 address were being sent to the host itself.
Instead, only send to host packets whose destination
address is host's local address.
Fixestailscale/tailscale#12448
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Co-authored-by: Andrew Dunham <andrew@du.nham.ca>
Add an additional RecorderAddrs field to tailscale.com/cap/kubernetes
capability. RecorderAddrs will only be populated by control
with the addresses of any tsrecorder tags set via Recorder.
Updates tailscale/corp#19821
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Return empty response and NOERROR for AAAA record queries
for DNS names for which we have an A record.
This is to allow for callers that might be first sending an AAAA query and then,
if that does not return a response, follow with an A record query.
Previously we were returning NOTIMPL that caused some callers
to potentially not follow with an A record query or misbehave in different ways.
Also return NXDOMAIN for AAAA record queries for names
that we DO NOT have an A record for to ensure that the callers
do not follow up with an A record query.
Returning an empty response and NOERROR is the behaviour
that RFC 4074 recommends:
https://datatracker.ietf.org/doc/html/rfc4074
Updates tailscale/tailscale#12321
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
This PR is in prep of adding logic to control to be able to parse
tailscale.com/cap/kubernetes grants in control:
- moves the type definition of PeerCapabilityKubernetes cap to a location
shared with control.
- update the Kubernetes cap rule definition with fields for granting
kubectl exec session recording capabilities.
- adds a convenience function to produce tailcfg.RawMessage from an
arbitrary cap rule and a test for it.
An example grant defined via ACLs:
"grants": [{
"src": ["tag:eng"],
"dst": ["tag:k8s-operator"],
"app": {
"tailscale.com/cap/kubernetes": [{
"recorder": ["tag:my-recorder"]
“enforceRecorder”: true
}],
},
}
]
This grant enforces `kubectl exec` sessions from tailnet clients,
matching `tag:eng` via API server proxy matching `tag:k8s-operator`
to be recorded and recording to be sent to a tsrecorder instance,
matching `tag:my-recorder`.
The type needs to be shared with control because we want
control to parse this cap and resolve tags to peer IPs.
Updates tailscale/corp#19821
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Add a new .spec.tailscale.acceptRoutes field to ProxyClass,
that can be optionally set to true for the proxies to
accept routes advertized by other nodes on tailnet (equivalent of
setting --accept-routes to true).
Updates tailscale/tailscale#12322,tailscale/tailscale#10684
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Also removes hardcoded image repo/tag from example DNSConfig resource
as the operator now knows how to default those.
Updates tailscale/tailscale#11019
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
cmd/k8s-operator,k8s-operator,go.{mod,sum}: make individual proxy images/image pull policies configurable
Allow to configure images and image pull policies for individual proxies
via ProxyClass.Spec.StatefulSet.Pod.{TailscaleContainer,TailscaleInitContainer}.Image,
and ProxyClass.Spec.StatefulSet.Pod.{TailscaleContainer,TailscaleInitContainer}.ImagePullPolicy
fields.
Document that we have images in ghcr.io on the relevant Helm chart fields.
Updates tailscale/tailscale#11675
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Irbe KruminaandGitHub
