Currently egress Services for ProxyGroup only work for Pods and Services
with IPv4 addresses. Ensure that it works on dual stack clusters by reading
proxy Pod's IP from the .status.podIPs list that always contains both
IPv4 and IPv6 address (if the Pod has them) rather than .status.podIP that
could contain IPv6 only for a dual stack cluster.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Adds a new reconciler that reconciles ExternalName Services that define a
tailnet target that should be exposed to cluster workloads on a ProxyGroup's
proxies.
The reconciler ensures that for each such service, the config mounted to
the proxies is updated with the tailnet target definition and that
and EndpointSlice and ClusterIP Service are created for the service.
Adds a new reconciler that ensures that as proxy Pods become ready to route
traffic to a tailnet target, the EndpointSlice for the target is updated
with the Pods' endpoints.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
The AddSNATRuleForDst rule was adding a new rule each time it was called including:
- if a rule already existed
- if a rule matching the destination, but with different desired source already existed
This was causing issues especially for the in-progress egress HA proxies work,
where the rules are now refreshed more frequently, so more redundant rules
were being created.
This change:
- only creates the rule if it doesn't already exist
- if a rule for the same dst, but different source is found, delete it
- also ensures that egress proxies refresh firewall rules
if the node's tailnet IP changes
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
* cmd/containerboot,kube,util/linuxfw: configure kube egress proxies to route to 1+ tailnet targets
This commit is first part of the work to allow running multiple
replicas of the Kubernetes operator egress proxies per tailnet service +
to allow exposing multiple tailnet services via each proxy replica.
This expands the existing iptables/nftables-based proxy configuration
mechanism.
A proxy can now be configured to route to one or more tailnet targets
via a (mounted) config file that, for each tailnet target, specifies:
- the target's tailnet IP or FQDN
- mappings of container ports to which cluster workloads will send traffic to
tailnet target ports where the traffic should be forwarded.
Example configfile contents:
{
"some-svc": {"tailnetTarget":{"fqdn":"foo.tailnetxyz.ts.net","ports"{"tcp:4006:80":{"protocol":"tcp","matchPort":4006,"targetPort":80},"tcp:4007:443":{"protocol":"tcp","matchPort":4007,"targetPort":443}}}}
}
A proxy that is configured with this config file will configure firewall rules
to route cluster traffic to the tailnet targets. It will then watch the config file
for updates as well as monitor relevant netmap updates and reconfigure firewall
as needed.
This adds a bunch of new iptables/nftables functionality to make it easier to dynamically update
the firewall rules without needing to restart the proxy Pod as well as to make
it easier to debug/understand the rules:
- for iptables, each portmapping is a DNAT rule with a comment pointing
at the 'service',i.e:
-A PREROUTING ! -i tailscale0 -p tcp -m tcp --dport 4006 -m comment --comment "some-svc:tcp:4006 -> tcp:80" -j DNAT --to-destination 100.64.1.18:80
Additionally there is a SNAT rule for each tailnet target, to mask the source address.
- for nftables, a separate prerouting chain is created for each tailnet target
and all the portmapping rules are placed in that chain. This makes it easier
to look up rules and delete services when no longer needed.
(nftables allows hooking a custom chain to a prerouting hook, so no extra work
is needed to ensure that the rules in the service chains are evaluated).
The next steps will be to get the Kubernetes Operator to generate
the configfile and ensure it is mounted to the relevant proxy nodes.
Updates tailscale/tailscale#13406
Signed-off-by: Irbe Krumina <irbe@tailscale.com>
Irbe Krumina