On some platforms (notably macOS and iOS) we look up the default
interface to bind outgoing connections to. This is both duplicated
work and results in logspam when the default interface is not available
(i.e. when a phone has no connectivity, we log an error and thus cause
more things that we will try to upload and fail).
Fixed by passing around a netmon.Monitor to more places, so that we can
use its cached interface state.
Fixes#7850
Updates #7621
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
We're using it in more and more places, and it's not really specific to
our use of Wireguard (and does more just link/interface monitoring).
Also removes the separate interface we had for it in sockstats -- it's
a small enough package (we already pull in all of its dependencies
via other paths) that it's not worth the extra complexity.
Updates #7621
Updates #7850
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
This is a follow-up to #7905 that adds two more linters and fixes the corresponding findings. As per the previous PR, this only flags things that are "obviously" wrong, and fixes the issues found.
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I8739bdb7bc4f75666a7385a7a26d56ec13741b7c
This adds an initial and intentionally minimal configuration for
golang-ci, fixes the issues reported, and adds a GitHub Action to check
new pull requests against this linter configuration.
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I8f38fbc315836a19a094d0d3e986758b9313f163
TestMonitorMode skips by default, without the --monitor flag, and then
it previously ran forever. This adds an option --monitor-duration flag
that defaults to zero (run forever) but if non-zero bounds how long
the tests runs. This means you can then also use e.g. `go test
--cpuprofile` and capture a CPU/mem profile for a minute or two.
Updates #7621
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Previously, when updating endpoints we would immediately stop
advertising any endpoint that wasn't discovered during
determineEndpoints. This could result in, for example, a case where we
performed an incremental netcheck, didn't get any of our three STUN
packets back, and then dropped our STUN endpoint from the set of
advertised endpoints... which would result in clients falling back to a
DERP connection until the next call to determineEndpoints.
Instead, let's cache endpoints that we've discovered and continue
reporting them to clients until a timeout expires. In the above case
where we temporarily don't have a discovered STUN endpoint, we would
continue reporting the old value, then re-discover the STUN endpoint
again and continue reporting it as normal, so clients never see a
withdrawal.
Updates tailscale/coral#108
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I42de72e7418ab328a6c732bdefc74549708cf8b9
The comment still said *magicsock.Conn implemented wireguard-go conn.Bind.
That wasn't accurate anymore.
A doc #cleanup.
Change-Id: I7fd003b939497889cc81147bfb937b93e4f6865c
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
So we're staying within the netip.Addr/AddrPort consistently and
avoiding allocs/conversions to the legacy net addr types.
Updates #5162
Change-Id: I59feba60d3de39f773e68292d759766bac98c917
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
These tests are passing locally and on CI. They had failed earlier in
the day when first fixing up CI, and it is not immediately clear why. I
have cycled IPv6 support locally, but this should not have a substantial
effect.
Updates #7876
Signed-off-by: James Tucker <jftucker@gmail.com>
We accidentally switched to ./tool/go in
4022796484 which resulted in no longer
running Windows builds, as this is attempting to run a bash script.
I was unable to quickly fix the various tests that have regressed, so
instead I've added skips referencing #7876, which we need to back and
fix.
Updates #7262
Updates #7876
Signed-off-by: James Tucker <james@tailscale.com>
This also adds a bunch of tests for this function to ensure that we're
returning the proper IP(s) in all cases.
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I0d9d57170dbab5f2bf07abdf78ecd17e0e635399
This makes `omitempty` actually work, and saves bytes in each map response.
Updates tailscale/corp#8020
Signed-off-by: Maisem Ali <maisem@tailscale.com>
Using log.Printf may end up being printed out to the console, which
is not desirable. I noticed this when I was investigating some client
logs with `sockstats: trace "NetcheckClient" was overwritten by another`.
That turns to be harmless/expected (the netcheck client will fall back
to the DERP client in some cases, which does its own sockstats trace).
However, the log output could be visible to users if running the
`tailscale netcheck` CLI command, which would be needlessly confusing.
Updates tailscale/corp#9230
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
The lazy initialization of the disco key is not necessary, and
contributes to unnecessary locking and state checking.
Updates #cleanup
Signed-off-by: James Tucker <james@tailscale.com>
Running tailscaled with the race detector enabled immediately fires on
this field, as it is updated after first read.
Updates #cleanup
Signed-off-by: James Tucker <james@tailscale.com>
A peer can have IsWireGuardOnly, which means it will not support DERP or
Disco, and it must have Endpoints filled in order to be usable.
In the present implementation only the first Endpoint will be used as
the bestAddr.
Updates tailscale/corp#10351
Co-authored-by: Charlotte Brandhorst-Satzkorn <charlotte@tailscale.com>
Co-authored-by: James Tucker <james@tailscale.com>
Signed-off-by: James Tucker <james@tailscale.com>
Identified in review in #7821 endpoint.discoKey and endpoint.discoShort
are often accessed without first taking endpoint.mu. The arrangement
with endpoint.mu is inconvenient for a good number of those call-sites,
so it is instead replaced with an atomic pointer to carry both pieces of
disco info. This will also help with #7821 that wants to add explicit
checks/guards to disable disco behaviors when disco keys are missing
which is necessarily implicitly mostly covered by this change.
Updates #7821
Signed-off-by: James Tucker <james@tailscale.com>
Make developing derp easier by:
1. Creating an envknob telling clients to use HTTP to connect to derp
servers, so devs don't have to acquire a valid TLS cert.
2. Creating an envknob telling clients which derp server to connect
to, so devs don't have to edit the ACLs in the admin console to add a
custom DERP map.
3. Explaining how the -dev and -a command lines args to derper
interact.
To use this:
1. Run derper with -dev.
2. Run tailscaled with TS_DEBUG_USE_DERP_HTTP=1 and
TS_DEBUG_USE_DERP_ADDR=localhost
This will result in the client connecting to derp via HTTP on port
3340.
Fixes#7700
Signed-off-by: Val <valerie@tailscale.com>
This commit implements UDP offloading for Linux. GSO size is passed to
and from the kernel via socket control messages. Support is probed at
runtime.
UDP GSO is dependent on checksum offload support on the egress netdev.
UDP GSO will be disabled in the event sendmmsg() returns EIO, which is
a strong signal that the egress netdev does not support checksum
offload.
Updates tailscale/corp#8734
Signed-off-by: Jordan Whited <jordan@tailscale.com>
This adds the util/sysresources package, which currently only contains a
function to return the total memory size of the current system.
Then, we modify magicsock to scale the number of buffered DERP messages
based on the system's available memory, ensuring that we never use a
value lower than the previous constant of 32.
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: Ib763c877de4d0d4ee88869078e7d512f6a3a148d
Noted on #5915 TS_DEBUG_MTU was not used consistently everywhere.
Extract the default into a function that can apply this centrally and
use it everywhere.
Added envknob.Lookup{Int,Uint}Sized to make it easier to keep CodeQL
happy when using converted values.
Updates #5915
Signed-off-by: James Tucker <james@tailscale.com>
This adds support to make exit nodes and subnet routers work
when in scenarios where NAT is required.
It also updates the NATConfig to be generated from a `wgcfg.Config` as
that handles merging prefs with the netmap, so it has the required information
about whether an exit node is already configured and whether routes are accepted.
Updates tailscale/corp#8020
Signed-off-by: Maisem Ali <maisem@tailscale.com>
Use the local context on Impl to check for shut down state in order to
drop rather than inject packets after close has begun.
Netstack sets endpoint.dispatcher to nil during shutdown. After the
recent adjustment in 920ec69241 we now
wait for netstack to fully shutdown before we release tests. This means
that we may continue to accept packets and attempt to inject them, which
we must prevent in order to avoid nil pointer panic.
References google/gvisor#8765Fixes#7715
Signed-off-by: James Tucker <james@tailscale.com>
This commit updates the wireguard-go dependency to pull in fixes for
the tun package, specifically 052af4a and aad7fca.
Signed-off-by: Jordan Whited <jordan@tailscale.com>
* wgengine/magicsock: add envknob to send CallMeMaybe to non-existent peer
For testing older client version responses to the PeerGone packet format change.
Updates #4326
Signed-off-by: Val <valerie@tailscale.com>
* derp: remove dead sclient struct member replaceLimiter
Leftover from an previous solution to the duplicate client problem.
Updates #2751
Signed-off-by: Val <valerie@tailscale.com>
* derp, derp/derphttp, wgengine/magicsock: add new PeerGone message type Not Here
Extend the PeerGone message type by adding a reason byte. Send a
PeerGone "Not Here" message when an endpoint sends a disco message to
a peer that this server has no record of.
Fixes#4326
Signed-off-by: Val <valerie@tailscale.com>
---------
Signed-off-by: Val <valerie@tailscale.com>
This adds support in tstun to utitilize the SelfNodeV4MasqAddrForThisPeer and
perform the necessary modifications to the packet as it passes through tstun.
Currently this only handles ICMP, UDP and TCP traffic.
Subnet routers and Exit Nodes are also unsupported.
Updates tailscale/corp#8020
Co-authored-by: Melanie Warrick <warrick@tailscale.com>
Signed-off-by: Maisem Ali <maisem@tailscale.com>
This change focuses on the backend log ID, which is the mostly commonly
used in the client. Tests which don't seem to make use of the log ID
just use the zero value.
Signed-off-by: Will Norris <will@tailscale.com>
Previously, it would accept all TCP connections and then close the ones
it did not care about. Make it only ever accept the connections that it
cares about.
Signed-off-by: Maisem Ali <maisem@tailscale.com>
This change adds a ringbuffer to each magicsock endpoint that keeps a
fixed set of "changes"–debug information about what updates have been
made to that endpoint.
Additionally, this adds a LocalAPI endpoint and associated
"debug peer-status" CLI subcommand to fetch the set of changes for a given
IP or hostname.
Updates tailscale/corp#9364
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I34f726a71bddd0dfa36ec05ebafffb24f6e0516a
Makes it cheaper/simpler to persist values, and encourages reuse of
labels as opposed to generating an arbitrary number.
Updates tailscale/corp#9230
Updates #3363
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
The debug flag on tailscaled isn't available in the macOS App Store
build, since we don't have a tailscaled binary; move it to the
'tailscale debug' CLI that is available on all platforms instead,
accessed over LocalAPI.
Updates #7377
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: I47bffe4461e036fab577c2e51e173f4003592ff7
Followup to #7177 to avoid adding extra dependencies to the CLI. We
instead declare an interface for the link monitor.
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
WSL has started to set the eth0 default route interface default to 1280
MTU, which is too low to carry 1280 byte packets from tailscale0 once
wrapped in WireGuard. The change down to 1280 is very likely smaller
than necessary for almost all users. We can not easily determine the
ideal MTU, but if all the preconditions match, we raise the MTU to 1360,
which is just enough for Tailscale traffic to work.
Updates #4833
Updates #7346
Signed-off-by: James Tucker <james@tailscale.com>
Uses the hooks added by tailscale/go#45 to instrument the reads and
writes on the major code paths that do network I/O in the client. The
convention is to use "<package>.<type>:<label>" as the annotation for
the responsible code path.
Enabled on iOS, macOS and Android only, since mobile platforms are the
ones we're most interested in, and we are less sensitive to any
throughput degradation due to the per-I/O callback overhead (macOS is
also enabled for ease of testing during development).
For now just exposed as counters on a /v0/sockstats PeerAPI endpoint.
We also keep track of the current interface so that we can break out
the stats by interface.
Updates tailscale/corp#9230
Updates #3363
Signed-off-by: Mihai Parparita <mihai@tailscale.com>
The log ID types were moved to a separate package so that
code that only depend on log ID types do not need to link
in the logic for the logtail client itself.
Not all code need the logtail client.
Signed-off-by: Joe Tsai <joetsai@digital-static.net>
To aid in debugging where a customer has static port-forwards set up and
there are issues establishing a connection through that port.
Signed-off-by: Andrew Dunham <andrew@du.nham.ca>
Change-Id: Ic5558bcdb40c9119b83f79dcacf2233b07777f2a
Updates #7123
Updates #6257 (more to do in other repos)
Change-Id: I073e2a6d81a5d7fbecc29caddb7e057ff65239d0
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Mihai Parparita
Andrew Dunham
Brad Fitzpatrick
Andrew Dunham
James Tucker
James Tucker
Maisem Ali
Charlotte Brandhorst-Satzkorn
Tom DNetto
valscale
Jordan Whited
Will Norris
valscale
Joe Tsai
Denton Gentry